GutterHawk Roofing & Gutter Specialists
Seamless Gutters in Crawfordville, FL
Crawfordville is the county seat of Wakulla County, an unincorporated town laid out along US 319, which runs through it as Crawfordville Highway on the way south from Tallahassee. The courthouse, the businesses on the highway and the subdivisions set back in the pines all deal with the same thing in a summer downpour: a lot of water leaving the roof edge at once and landing on sandy ground that sits only about 16 feet above sea level.
GutterHawk installs seamless gutters in Crawfordville, FL from a trailer-mounted forming machine that we tow to the house. Each run comes off the coil at the exact length of that stretch of eave, so the long run over a garage or a back porch is one piece of metal instead of a row of short sections lapped together, and the only joints left are the corners, outlets and end caps.
Below is how we pick the size, metal and color for a Crawfordville home, how the day of the install goes, and what moves the price up or down.
In Crawfordville, GutterHawk also handles gutter guards and roof replacement. Closer to town? See our seamless gutters in Tallahassee page.
What We Form for Crawfordville Homes
- 5-inch K-style aluminum, enough for a modest roof plane on a single-story ranch
- 6-inch K-style aluminum for big or steep roof sections and for metal roofs that shed water fast
- Heavier-gauge aluminum where pine and oak limbs can drop onto the gutter
- Half-round on request, priced higher because it uses more material and forms more slowly
- Copper for homes where the gutter is part of the look, at several times the cost of aluminum
- Factory colors baked onto the coil, chosen to match the trim, the roof or a deliberate contrast
Heavy Rain on Flat, Sandy Ground
The Tallahassee area gets more than 55 inches of rain a year, and a good share of it arrives in short, hard afternoon storms. In Crawfordville that water lands on ground with very little fall to it. A downspout that empties right at the slab leaves a soaked strip along the wall that can stay wet for days, and the splash marks the bottom course of siding and the foundation face.
So on a Crawfordville job the downspouts get as much attention as the gutter. We look at which way the yard drains, where the driveway and walks sit, and where water stands after a storm, then place the outlets to carry it away from the house. Extensions running three to six feet from the wall handle most homes. Where the grade tilts back toward the house, underground drainage piped out to a discharge point farther away is the better fix, and we will say which one your lot needs when we measure.
Homes Built in the Pines
Crawfordville sits on the edge of the Apalachicola National Forest, and many homes in and around town stand on lots cleared from pine woods, with trees left along the property lines or close to the house for shade. That shade brings a steady fall of pine straw all year, plus oak leaves in the fall where hardwoods are mixed in.
Pine needles lie flat in a trough and knit into a mat that holds water against the metal. A seamless run has no seam laps along its length for that mat to snag on, which helps, but needles still collect at the outlets and corners. If your roof sits under tall pines, ask about gutter guards at the same visit. We fit micro-mesh, the type LeafFilter is best known for, as well as reverse-curve and lower-cost screen options, and we will tell you which one fits the trees over your house.
A Growing County Seat
Crawfordville has been the seat of county government for a long time. The Old Wakulla County Courthouse, a wood-frame building completed in 1894, was listed on the National Register of Historic Places in 1976. The town has also grown fast lately: the census counted 3,702 residents in 2010 and 4,853 in 2020.
That mix shows up on our estimates. On an older house we pay close attention to the fascia, because trim that has had water running behind a leaky gutter for years can look fine from the yard and be soft to a screwdriver. Rotted board is shown to you and quoted on its own before any new gutter is hung on it. On a newer house the question is usually coverage and size: gutters on only part of the roofline, or 5-inch where a large roof plane really needs 6-inch. We can extend or replace the system so every eave drains.
How the Install Day Goes
We start by walking the roofline, measuring every run and noting where valleys dump a lot of water into one spot. The old gutter comes down and is hauled away, and the fascia behind it gets checked before anything new goes up.
Then the forming machine is set up in the driveway. Coated coil feeds in one end and finished gutter comes out the other, cut to each measurement and carried straight up the ladder. It is hung on hidden hangers screwed into the fascia, pitched toward the outlets, and the corners and end caps are sealed. Downspouts go where the water needs to go on your lot, not simply the shortest drop. Before we pack up, every run gets a hose test so you can see it carry water to the outlets. Most homes are finished in a single day.
If you know a spot where water pours over or pools after rain, show the crew before work starts. That kind of firsthand detail changes downspout placement more often than any measurement does.
Gauge and Color Choices
Most homes get .027 or .032 gauge aluminum. The heavier stock resists dents from falling limbs and from ladders leaned against it later, and it stays straighter on long runs, so it is worth considering if your house is under trees. Aluminum does not rust, which is why it goes on the great majority of homes we do.
Color is baked onto the coil at the factory, and since a gutter traces every eave of the house it is one of the most visible choices you will make on the outside of the house. Most owners match the trim so the gutter blends into the fascia. A dark gutter against a dark roof frames the house and hides streaks, and black on a white house turns the roofline into a feature. Remember the downspouts run down the walls, so check the color against the siding too. Your estimator brings samples to hold up against the house.
What Sets the Price
Seamless gutter is priced per linear foot, and that rate moves with the size, the material, the gauge and the height of the work. Six-inch costs more than five-inch, copper costs several times as much as aluminum, half-round costs more than K-style, and a two-story run takes more setup than a single-story one.
Downspouts are counted separately, and so are gutter guards and any fascia repair, so the quote shows exactly what each part costs. We measure the house before we put a number on it and give you the quote in writing, rather than guessing from the street.
Get Seamless Gutters in Crawfordville, FL
Our crews come down US 319 from our two Tallahassee offices on North Monroe Street and Shamrock Street. GutterHawk’s owner, Jared Reinstein, has worked in the seamless gutter industry since 1993 and holds a Certified Building Contractor license, CBC 1255295, and we are GAF certified. For seamless gutters in Crawfordville, FL that are sized to your roof and formed on site, call (850) 779-1081 and ask for a measured quote.
Frequently Asked Questions
Do you form the gutters at my house in Crawfordville?
Yes. We bring a trailer-mounted forming machine and run each piece to length in your driveway, so long eaves are one continuous run.
Is 5-inch gutter enough for my roof?
Often it is on a small single-story roof. Large or steep roof planes, and metal roofs, usually call for 6-inch with bigger downspouts.
What can I do about water standing next to my foundation?
Move the discharge away from the wall. Downspout extensions of three to six feet fix most cases, and underground drainage handles lots that slope toward the house.
Will seamless gutters stop pine straw from clogging?
No gutter does that on its own. Seamless runs have fewer places for needles to catch, and a micro-mesh guard is the most reliable way to keep pine straw out.
My fascia looks soft. Can you still install?
We replace rotted fascia first, because a new gutter will not hold on wood that will not hold a screw. We show you the damage and price the repair separately.
Do you put seamless gutters on new construction in Crawfordville?
Yes. We can add gutters to a new house or extend a partial system so every eave drains.
What do seamless gutters in Crawfordville, FL cost?
They are priced per linear foot, depending on size, material, gauge, height and downspout count. We measure first and quote in writing.
Q.2 Aluminum or copper?
Aluminum for nearly everyone. Copper for period homes where appearance justifies several times the cost.
Q.3 K-style or half-round?
K-style carries more water for its size. Half-round suits historic homes and sheds debris better.
Q.4 Do I need 5 inch or 6 inch?
It depends on the roof area and pitch draining into each run. Many homes here need 6 inch.
Q.5 Can you match my existing trim color?
Yes. Aluminum coil comes in a wide range of factory colors.
Q.6 How long does installation take?
Most homes are a single day, including removing the old system.
Q.7 How much do seamless gutters in Havana FL cost?
Priced per linear foot, varying with material, gauge, size, and height. We quote after measuring.
Working With Us Is Easy
01.
Request Your Quote
Getting the process started is easy! Simply fill out our quick form or call us at (850) 779-1081. One of our friendly staff members will get in touch to finalize the details.
02.
We Work On Your Estimate
One of our expert estimators will get to to work analyzing your job and crafting a proposal. Of course, we’re here to answer any questions you may have.
03.
GutterHawk Gets To Work!
Contact Us
Have questions about your roof? Do you need information on gutter maintenance plans? No matter the question, GutterHawk is here to help!
